MeFoto GlobeTrotter Carbon Review

The MeFoto tripods are a line of tripods that was spun off from Benro.  They are inexpensive and compact, clearly targeting the traveler as the GlobeTrotter name would suggest.  The GlobeTrotter is the largest model in MeFoto’s line and should thus be the most capable of supporting a wide range of equipment. 

This is the sister review of the Aluminum version of the same tripod, which can be found here.  These reviews will share some pictures, and have some unique ones that apply to both tripods.  I will be highlighting the differences as well for those who are trying to choose between the two.  Most of the text however, will be identical.

Specifications

This is an abbreviated list.  The full measured specs can be found here.

Weight2.98 lbs (1.35 kgs)
Maximum Height51.3 in (130.3 cm)
Minimum Height17.6 in (44.7 cm)
Max Height with Center Column60.3 in (153.2 cm)
Folded Length16.1 in (40.9 cm)
Folded Volume227.0 cu. in. (3.7 liters)
Leg MaterialCarbon Fiber
Leg Sections5
Primary Leg Angle24 deg
Leg LocksTwist
Exchangeable FeetYes
Foot TypeRubber
Bottom HookYes
Retail Price$350

Note that for consistency of comparison between other tripods, these measurements are made without the included ballhead.

MeFoto claims that the tripod will support 26.4 lbs, but in the same breath says that it will support up to a DSLR and 70-200 f/4 steady.  This highlights the misleading nature of the weight rating given by tripod manufacturers.  While the tripod can technically support the weight, it can never hold a camera and lens of that weight steady.

Features

The MeFoto GlobeTrotter is packed full of all the features they could cram in.  There is a a center column, bottom hook, and removable feet.  These are pretty standard.

Becoming more standard for travel tripods, including this one, is the ability for the legs to fold all the way up, letting the head and center column rest between them.  The beauty of this is that the entire tripod, when folded up, is quite short and can therefore fit into just about any bag or suitcase.  The downside is that this operation rather increases the diameter of the folded tripod, and so the actual volume it takes up is still rather large.  If you are okay with removing the tripod head when length is critical, the traditional design tends to be more compact overall.

The GlobeTrotter also has the ability to convert into a monopod by removing one of the legs and screwing it to the bottom of the center column.  If you find yourself wanting both a monopod and tripod while traveling, this is a great feature.  If you have never had that though, you probably don’t need this feature.

A MeFoto Q2 ballhead is included with the GlobeTrotter line.  It is a perfectly adequate low-end ballhead that takes standard Arca-Swiss style plates.  It has a panning lock knob, tension knob, and main lock knob.  It is perfectly adequate for anything the GlobeTrotter tripod legs are designed to handle.

Use

I experienced no significant problems in handling the tripod, except that it is time consuming.  Whenever I unfold the tripod, I have to pull each leg 180 degrees, push the angle tab into place, and then unscrew and tighten four lock knobs on each leg.  Then open the legs to the correct angle, place the tripod down, and lower the center column.  This is time consuming.  I can setup my RRS TFC-14 in about 10 seconds.  The GlobeTrotter, from a fully folded state, took me 35 seconds.  If you are spending all day shooting, this isn’t a big deal.  But if you are on the go, and needing to pack up in between shots, this would quickly become a nuisance.

Build Quality

The build quality of the GlobeTrotter is very reasonable for a tripod at this price point.  The fit and finish are better than expected.  The Aluminum pieces that make up the spider and leg locks are nicely smoothed and colored.  Some details were clearly cut in the design.  There are no rubber gaskets on the leg locks to prevent moisture from seeping into the legs.  The rubber on the leg locks has a tendency to slip, and no grease has been applied to the threads on the leg locks.

Test Results

The full test data can be found here.  The table below summarizes the results.

Stiffness About Vertical Axis338 +/- 2 Nm/rad
Damping About Vertical Axis0.12 +/- 0.012 Js/rad
Stiffness About Radial Axis1241 +/- 6 Nm/rad
Damping About Radial Axis0.272 +/- 0.027 Js/rad

These numbers are somewhat poor, but in line with what we expect from tripods at this price point.  With this kind of stiffness, the user would struggle to get sharp images with the advertised DSLR and 70-200 f/4 lens.  This is not enough stiffness to adequately damp the mirror slap or prevent wind from moving the camera around.  The tripod will be much more at home supporting smaller, short telephoto to wide angle lenses.  The overall stability of the carbon version isn’t really that much better than the aluminum one.  This seriously calls into question the quality of the carbon fiber being used as good carbon fiber should be noticeably stiffer than aluminum of the same dimension.

Summary

The GlobeTrotter is a mixed bag.  It is full of features, has decent build quality, and a low price.  However, the uninspiring stiffness limits the tripod’s range of applications.  If Mefoto made a four section version of this tripod, sans features, I think they could provide a really good tripod, as opposed to just an acceptable one.

Pros

  • Good build quality
  • Built-in monopod
  • Short folded length

Cons

  • Features all add weight
  • Mediocre stiffness
  • The Carbon version is less stiff than the Aluminum one

If you are looking for a tripod, need the aforementioned features, portability, and low cost but don’t need to be on the forefront of weight or rigidity, this could be a good tripod for you.  The aluminum version appears to be the better value, given that it is just as stiff as the carbon version.

Acceptable