In testing tripods, I have noticed some patterns in their performance with respect to design. Some of these are obvious, such as tripods with skinny legs tend to perform worse than those with fat ones. Less obvious is the tripod performance with respect to the angle with which the legs splay outwards. It seems that tripods with legs that splay outwards more have better yaw (axial or pan) stiffness and thus better overall performance than their narrower counterparts. In this post we are going to explore that assertion more thoroughly.
From the perspective of the manufacturer, it is certainly appealing to err on the side of narrower leg angle. The tripod will be lighter and/or taller than if the leg splay were wider, padding the spec sheet. In addition, the overall material cost will be a little bit lower. There are strong use reasons not to want the leg angle to wide as well. Too wide of a stance becomes cumbersome and unwieldy. If used in a populated area, the tripod becomes that much more prone to blocking pathways and getting in the way of the photographer. A wider stance tripod is much less prone to tipping over though, and as we shall see, also produces better overall stiffness.
Lets take an overview of the anecdotal evidence referenced above. Below is the ratio of the pitch versus yaw stiffness of each tripod I have tested versus its opening leg angle.
There is a clear upward downward trend as the leg angle opens up. This plot is showing us that there is clearly an effect on the stiffness due to leg angle, but doesn’t say anything about the overall performance of the tripods in question. Clearly though tripods with a wider stance have much better yaw stiffness with respect to their pitch stiffness. On the extremes we have the Feisol CT3442 Tournament and the Really Right Stuff TVC23. The RRS is an outstanding performer, while the Feisol is merely okay. There are a lot of good and bad tripods in between.
To better understand the effect leg angle has on performance, we need to test a single tripod at a variety of different leg angles. The tripod I have chosen for this test is the RRS TVC23 because it has the widest native spread. Thus, by inserting shims between the pull tabs and the apex, I can methodically decrease the leg angle. The shim is simply aluminum foil. This is ideal for being thin and allowing for small angle changes and also for maintaining full metal to metal contact between the leg and the apex.
The bar shown on top is simply the standard test apparatus. After inserting the foil, the angle of each each leg was measured. The results were averaged and that is the reported value for the leg angle. I took three measurements at each leg angle and each one is plotted on the charts below. First, lets take a look at the Yaw Stiffness:
That is a beautiful set of data. All of our suspicions regarding the effects of leg angle on yaw stiffness are confirmed. The yaw stiffness of the tripod increases dramatically as the legs splay out further. Going even from the common leg angles of 22.5 degrees to 25 degrees results in a 15% increase in the yaw stiffness.
The results for the pitch stiffness are decidedly less dramatic. There appears to be a slight increase in stiffness as the leg angle decreases, but its difficult to say as differences aren’t that far above the noise level. If the measured effect here is real, it would be entirely imperceptible in use. I deliberately let the graph continue all the way down to zero to emphasize how little effect is seen here. If I were able to test larger leg angles than the native 26.5 degrees on the TVC23, I would expect the stiffness to fall off eventually. The above data encompasses the entire normal range of values found on tripods for the primary leg angle though, so one would have to be using the tripod with the legs splayed out to a different setting to see an effect.
If we construct the same plot as the first one looking at the ratio of the stiffness with the TVC23 data, we get:
The overall trend is clearly the same, though from the data we know that the effect is dominated by the change in yaw stiffness.
There is some clear structure to the damping data, but not quite as clear as the stiffness. This is a direct result of the damping measurement being much noisier and that the damping behavior is less linear than stiffness. At any rate, there is a clear drop off in the yaw damping to accompany the drop off in yaw stiffness as leg angle decreases. The difference is not as large though.
The implications here are non-trivial. Wider leg angle results in better tripod performance. Clearly there are good reasons to use a narrower leg angle. A narrower angle improves the height/weight ratio and reduces the overall footprint. This last point is not inconsequential when using the tripod in confined or crowded spaces such as a studio, busy street, or crowded viewpoint. The optimal leg angle for a tripod then becomes somewhat subjective. It depends on the application and preference of the user. Those looking to optimize performance may want a wider leg angle, while others may want the more compact package of a narrower one.
For me, I prefer a wider leg angle. For example, lets consider two hypothetical tripods that are otherwise identical except one has a leg angle of 22.5 degrees, and the other is at 25 degrees. The data above shows that the second one would be roughly 15% stiffer in the yaw direction, which is the weakest and therefore the most critical direction of motion. Using a little trigonometry, we can see that this second tripod would only be 2% shorter than its 22.5 degree sibling. That’s a trade off I would happily make.
It would be interesting to see how other tripods perform under the same test. The results here are so strong though that I doubt the conclusion would be any different. Tripods are mostly built in the same way. At some point I also want to test the stiffness beyond the maximum 26.5 degree leg angle if the RRS TVC23. This will require something more complicated than simply using some aluminum foil shims, such as 3d printing some custom pull tabs. So that is a project for down the road.
Thanks once again Dave for doing these tests and
sharing the results!
I’m wondering if the trend continues if you splay th
e legs more like setting the legs to the second or th
ird tab stops. I imagine, perhaps past 45 degrees, t
hat stiffness may fall because the leg angles cause
loss of mechanical adantage.
The trend almost certainly continues. Unfortunately the test method with aluminum foil didn’t allow me to continuously test beyond the first angle stop. I should test around the second leg stop as well, which I will likely do in a future post at some point. Ideally I would like to be able to test the full range, from 0 deg to 90 deg, but that will require me to make some more specialized equipment. I don’t feel like I have good intuition as to when the yaw stiffness might peak.
Perhaps a compromise approach would be to test at the available stop angles (particularly as these are
what most users will choose v adjusting angles with shims). This will of course reduce available data for
analysis, but may better show ‘real world’ values for particular tripods.
Yes, this is something I have been meaning to do as well. I didn’t take this approach for the first test as most tripods only have three stops. I am very interested in the stiffness behavior as the tripod gets really close to the ground with spread legs though.
While “how would this tripod perform if the angle at first stop was different” is an interesting question, I would argue that the more practical one of the effect of different angles without stop is at least as interesting.
And that one would allow for more ways to test, to mind come spikes or rock clamps on appropriately rough concrete floor and – especially for the more extreme angles- coming up with some DIY ground spider like video tripods tend to have to prevent the legs from spreading further.
This is making me want to test my
CT-3342 to see if it has the same
stiffness ratio as the 3442 you tested.
I happen to have a stiff bar with
weights that was once part of a
homemade steadycam, but I’m not sure
if it’s quite enough inertia to get a
useful sampling frequency with an
accelerometer. Maybe I can rig up
some magnet with a coil and hook it
up to a microphone port on my
computer to get really fast sampling…
Using a magnet and coil with the built in A/D on your computer sounds like a really good idea. It would be surprising to me if that actually works much better than the accelerometer, which is lowpass filtered to a 50hz bandwidth. Depending on the amount of inertia used, you may have to add the inertia of the tripod itself to get accurate results. For me the tripod inertia is less than 1%, usually much less, so I ignore it.
It’s certainly not a factor of 100
different, but maybe I could test it
with two different test inertias and
fit it to figure out the effective
inertia of the tripod itself.
Hi, Great site! I’ve been thinking a
lot about these things!
When I set up my tripod I want to
know what leg angle i need to use to
get the best performance for a given
height. I have lots of leg length to
spare, as i’m using an extra tall
tripod (GT5542LS). It would be great
to have an answer to that! In
practice I found that the optimum is
somewhere around the first angle stop
of my tripod, at least with my
typical equipment mounted (a 1.5 kg
spotting scope) and somewhat
demanding wind conditions (4-5
beaufort), where at some point i get
into resonances as with increasing
wind speed the inherent resonance
frequency of the Kármán vortex street
around the legs increases, reaching
the resonance frequency of the
tripod+scope somewhere around 5 bft
wind strength. At least that’s what I
assume is happening.
I think that the answer of what the
optimal angle is will differ
depending on what type of tripod we
use. Mono-tube (e.g. manfrotto xprob)
vs double-tube designs (e.g. Sachtler
CF 100). Where the optimal angle
should be narrower with the double
tube design, with the disadvantage
that the double tube design is
terrible if the legs are spread out
completely (90°), a situation where
the single-tube design is quite good.
For this reason, many double-tube
designs don’t actually allow that and
require the use of a spreader (e.g.
mid-level spreader or ground
spreader) because they are also don’t
have angle stops at the shoulder
joints. The “pure” double-tube design
for me is one where the shoulder
joint rotates completely freely, so
that no forces can be transmitted in
the rotation direction, whereas i
consider the single-tube design to
have some friction there.
Many tripods are somewhere in
between, for example the
berlebach-tripods, or the sachtler
flowtech tripods. The berlebach
tripods are technically double-tube,
but their “tubes” are not actually
tube shaped, but approximately
square, with the suqares sides having
unequal length. The sachtler
flowtechs are technically
single-tube, but again the tubes are
not round, this time with the longer
axis beeing in the other direction.
Both the berlebach and flowtech
tripods provide some of the advantage
of beeing stiffer at shallower leg
angles (thus greater height per leg
length) while also allowing use at
90° leg angles and providing angle
stops at the shoulder joints, thus
not requiring the use of a spreader.
At first I would like to thank you for all these
tests, you are doing a great job!
It seems that Feisol has changed the primar
y leg angle to 25 degrees in the current versi
on of ct-3442. Would it be possible to repea
t the test for this model? I think seeing the c
omparison would be interesting.
To the best of my knowledge the specification on their website is wrong and they are still shipping tripods with a 20 degree leg angle.
I have no idea what the current status i
s, but I just read this topic: https://www.
dpreview.com/forums/thread/4313080,
where someone claims to have measur
ed the recently purchased tripod (which
was over a year ago) and has an angle
25 deg. Perhaps there are still versions
with a 20 degree angle on the market, a
nd newer ones are 25 degrees? I ask be
cause it’s not so difficult to measure the
angle, right? Especially when it must be
an argument in the discussion. 🙂
Regards
The CT-3442 Tournament I reviewed with a 20 degree leg angle was purchased just under a year ago. It is certainly possible it was old stock and that they have switched. And yeah, it isn’t difficult to measure leg angle accurately. You can do it with a protractor app on a phone. At this point, I will believe that feisol has switched to 25 degrees when I see someone actually measure one and take a picture. I certainly hope they do make the leg angle wider, it would make for a better tripod.
Just curious if we are discussing
the angle between two adjacent
legs, or the angle between a leg
and the vertical axis of the
tripod? Isn’t the latter what we
want? And could this confusion
be leading to the 20 v 25 degree
readings on the CT-3442?
I’m enjoying these discussions
immensely. Thank you.